any rev made to this print must have an updated mkt print do not scale from this print .134.003 3.410.08 .104 ref 2.64 .012 0.31 (see note 9) .139 3.54 "a" "a" item no. part number quantity material 1 ASP-103597-01-B 1.0000 ul 94 v0, color: black 2 c-226-03-h 114.00 phos bronze, 521 hard temper 3 sdb-030-9653 114.00 96.5% sn/3% ag/.5% cu 4 k-850-650 1.0000 polyimide film 5 ct-asp1132ms .0015 conductive polymer .145 3.68 ref .095 2.41 ref .970 ref 24.64 1.070 ref 27.18 .320 ref 8.13 .354 8.99 .035 ref 0.89 .900.002 22.86 0.05 (19 pos - 1) x .050[1.27]) .250 6.35 .308.020 7.820.51 .017.010 0.430.25 c1 19 a b c d e f 01 'b' section "a"-"a" 1 2 3 4 1.732 44.00 ref .630 16.00 ref user direction of un-reeling pocket not detailed 5 detail 'b' scale 4 : 1 see note 13 see note 14 c packaging view in-process without solderballs sheet of unless otherwise specified, dimensions are in inches. tolerances are: decimals angles .xx: .01 2 .xxx: .005 .xxxx: .0020 vita 42 lif (lead free) socket assembly by: asp-103612-04 dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing rrc 10/13/06 2 1 sheet scale: 3:1 f:\dwg\misc\mktg\asp-103612-04-mkt.slddrw plating: contact area: .000030 gold over .000050 nickel remainder: .000003 flash gold over .000050 nickel notes: 1. use lead free solder balls & ASP-103597-01-B body for non-standard 19 position. 2. represents a critical dimension. 3. burr allowance: .0005[0.013] max. 4. minimum pushout force: .5 lb. 5. maximum allowable bow: .002[0.05] inch/inch after assembly. 6. note deleted. 7. one reel minimum plating requirement (85,000 contacts per reel). 8. all dims to be symmetrical about the centerline within .001[0.03]. 9. maximum variation between solderballs: .0025[0.064] 10. refer to visual inspection board for solderball appearance checks. 11. the distance from the center of any solderball to the center of any adjacent inner peg shall be .025.005[0.640.13]. 12. parts to be packaged in tape & reel. 13. contact to be flush: .002 [0.05]. 14. no flash allowed on the pin tips. 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322 revision h
.9000 22.860 .2500 6.350 'c' recommended board layout 01 19 .0100 0.254 trace .0200 0.508 pad .0100 0.254 via (plated) .0250 0.635 pad .0310 0.787 free of solder mask .0250 0.635 45 detail 'c' scale 12 : 1 .900 22.86 .050 1.27 (typ) .250 6.35 .050 1.27 (typ) .0250 0.635 (typ) 01 19 recommended stencil layout stencil to be .0060[0.152] thick note: outer rows may not need vias - this is left to the discretion of the board designer. a b c d e f a b c d e f sheet of vita 42 lif (lead free) socket assembly by: asp-103612-04 dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. rrc 10/13/06 2 2 sheet scale: 4:1 f:\dwg\misc\mktg\asp-103612-04-mkt.slddrw revision h 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322
|
